› It is a tool used for quick and professional removal and installation of suspension struts.
› Designed for the McPherson struts with crown and cylinder springs
› High capacity of max. Load: 26,000 Nm
› Min. Spring diameter 80 mm
› Max. Spring diame
› It is used for quick and professional compressing of coil springs.
› The compression force is approximately 1200 kg.
› The maximum gap is 300 mm.
› It has 3 compressing head pairs that are
70-105 mm, 90-140 mm, and 130-190 mm long.
› It has a speci
It has threaded rods, hook (M20 x 2.5) and a powerful square tube for mounting and demounting of the engine and transmission.
Its width is adjustable. Protects the fenders by its rubber pads. It has a double chain with a length of 90 cm.
› It is used for checking and dismounting of engine, transmission box and rear axle.
› Its approximate height is 140 to 195 cm.
› It has 4 caster wheels.
› It has a compact and lightweight structure.
› Provides wide lifting range.
› Due to its hydrau
› It is used to lift the vehicles.
› It has a length of 310 mm,
› A width of 265 mm and
› A height of 460 mm.
› Its maximum lifting height is 613 mm,
› The minimum lifting height is 395 mm and
› The lifting capacity is 6000 kg.
› It is used to lift the vehicles.
› It has a length of 225 mm,
› A width of 205 mm and
› A height of 360 mm.
› Its maximum lifting height is 428 mm,
› The minimum lifting height is 288 mm,
› And the lifting capacity is 3000 kg.
› Vehicle lifting jack with polished and machined cylinder.
› Uses high performance seals.
› It extends the life of the seals by minimizing the wear.
› It has a transport trolley with 2 wheels and a carrying handle.
› The minimum height is 90 mm and
› Is a lifting trolley jack with the polished and machined cylinder.
› That uses high-performance gaskets.
› It extends the life of gaskets by minimizing corrosion.
› It has a 2-wheeled transport cart and a carrying handle.
› It has a length of 640 m
› The spring compressor tool is an ideal product for installing and
removing the spiral spring on the front and rear axles.
› It has stepless adjustment, easy and safe use.
› Spring tension for spiral springs is 1500 kg (1.5 tons).
› Width 280 mm.
›
Used for fast and professional changing of the axial joints of cars and light commercial vehicles and automatic clamping of the joint heads. Provides easy assembly of long tie rods because of its open structure.
Saves up to 3 hours of working time.
›
Used for fast and professional changing of the axial joints of cars and light commercial vehicles and automatic clamping of the joint heads. Provides easy assembly of long tie rods because of its open structure.
Saves up to 3 hours of working time.
›
› It is a hydraulic reverse puller used in passenger cars, heavy vehicles, tractors and situations that require reverse pull.
› Min. Length: 540 mm
› Max. Length: 670 mm
› Working Pressure: 68 Mpa
› Stroke: 130 mm
› Read the instructions before use.
Scope of delivery: 1 x BRIO driveshaft extractor set 3 in 1
Drive shaft extractor set is special product for hydraulic wheel hub puller for perfect assembly and disassembly of wheel bearings. Especially suitable for glued and rusted drive shafts moun
› It is forged and reversible.
It has the following technical properties:
› Clamping depth: 150 mm
› Hooked foot: 10.5 mm
› Hook length: 28 mm
› Min. clamping width: 25 mm
› Spindle length: 175 mm
› Hex drive size: SW 17
› Max. clamping width: 160 mm
